Controls & Vision

Topic	Replies	Views	Activity
X20BC008T OPC UA PubSub multicast: subscriber receives only from sources within its /22 subnet? x20 Hello B&R Community, We are investigating an OPC UA PubSub UDP/UADP multicast reception issue with an X20BC008T running firmware 1.7.1. The subscriber writes an Int16 value to AnalogOutput01 of an X20AO4622 module. Set…	1	33	November 4, 2026
About the Controls & Vision category	1	54	November 6, 2025
X90 with X67BC8321.L12 and X67IF1121-1 causes service mode RS232 Serial x90	4	47	November 4, 2026
Hardware configuration with 4PPC650, X20BC1083 and X20SLX806 mapp-safety , t-c-panels , safety_plus	5	51	November 3, 2026
X20AI8039 filter automation-studio , plc , io	7	101	November 3, 2026
CPx68x Power Supply Diagnostic x20	1	47	October 31, 2026
X20PS9600 LEDs and RS485 frame error x20 , fieldbus	5	109	October 30, 2026
0g2001.00-090 pg2000	8	87	October 30, 2026
Camera has CameraStatus 3 mapp-vision	3	71	October 29, 2026
Error 6910 compiling Projekt AS4.2.7.54 with safedesigner 4.2.5.4 and SafetyRelease 1.6 integrated-safety , automation-studio	7	178	October 29, 2026
CAN communication with ArCan - Receive wrong ID issue can	5	133	October 28, 2026
Can an X20 PLC receive RS-485 frames with a 9-bit address-mark byte? fieldbus	1	61	October 28, 2026
SafeDESIGNER 4.4.1.0: "The current configuration of access modules is invalid!" immediately when opening SafeDESIGNER automation-studio , windows	2	64	October 22, 2026
SafeDesigner project dynamic password for CRA? mapp-safety	2	153	October 21, 2026
Does the node "Root/Objects/DeviceSet/X20BC008T/X2X IF1/Status" of X20BC008T support? automation-studio	5	112	October 12, 2026
Libary to controll a Nanotec Controller via Modbus RTU fieldbus , plc , modbus	6	491	October 7, 2026
Node number not recognised power-panel	3	124	October 2, 2026
X20cp1483-1 x20 , plc	12	404	October 2, 2026
New APC - Win11 - Hypervisor - Dual Monitor Setup - Retrofit apc-ppc	5	127	October 1, 2026
X90cp154.60-s1 problem mapp-safety	30	354	September 30, 2026
Unable to Restore Communication with B&R PLC After putting it on Boot Mode automation-studio , plc	5	132	September 29, 2026
SafeDesigner+ Report is incomplete safety_plus	4	124	September 29, 2026
Murrelektronik Cube67 Configuration with B&R EtherCAT Master ethercat	4	136	September 29, 2026
When inserting 5LS182.6-2 card in APC910B2 PLC does not startup apc-ppc	3	103	September 28, 2026
X90 built-in CANopen master resets ABB ACS880 (FCAN-01) drive parameters on startup — how to disable the node reset / parameter download? x90 , can-open	4	158	September 22, 2026
How to update the firmware of an X20AT4222 module connected behind a BC0063 bus controller (e.g. with an ABB PLC, no B&R CPU) x20	1	69	September 18, 2026
Application Use case for X20CM0985-02 x20	2	91	October 5, 2026
Adding of RemoteConfiguration in SafeDesigner+ safety_plus	6	209	September 11, 2026
B&R X20AI/AO modules not detected x20 , automation-studio	4	113	September 4, 2026
Communication between AS4.12 Safety Release and AS4.12 mapp Safety 5.24.2.1 SF Domain mapp-safety	1	57	September 4, 2026

X20BC008T OPC UA PubSub multicast: subscriber receives only from sources within its /22 subnet?

x20

Hello B&R Community, We are investigating an OPC UA PubSub UDP/UADP multicast reception issue with an X20BC008T running firmware 1.7.1. The subscriber writes an Int16 value to AnalogOutput01 of an X20AO4622 module. Set…